How to use a clapperboard
For film and video shoots with separate sound. Updated 12 November 2026.
This page covers the head slate on a take with sync sound, then the four other marks a 2nd AC uses: MOS, tail slate, second sticks and soft sticks. The clap gives the editor one frame in the picture and one spike in the sound to line up. What is written on the board tells them which scene and take they are looking at. Calls vary from crew to crew; on a set, the 1st AD's version wins.
- Clapperboard cheat sheet, printable PDF (one page, US Letter: the call and what to write on the left; MOS, tail slate, second sticks and soft sticks on the right)
The call, in order
Before the call, the board is filled in, the sticks are open, and the 2nd AC is standing where the 1st AC wants it: in focus, large enough in frame to read, and as close to the lens's line as the shot allows.
- The 1st AD calls "Lock it up," then "Quiet, please."
- The 1st AD calls "Roll sound." Sound rolls the recorder and answers "Speed" (the mixer, or the boom operator when the mixer is at the cart).
- The 1st AD calls "Roll camera." The camera operator or 1st AC answers "Rolling" (some crews say "Speed" here too).
- The 2nd AC holds the board still in frame with the sticks open and reads it out: "Scene twelve Apple, take three." The setup letter is said as a word: Apple, Baker, Charlie, Dog, or Alpha, Bravo, Charlie, Delta, depending on the crew.
- The 2nd AC says "Mark," finishes the word, then closes the sticks once, firmly, with the board held still so the frame where the sticks meet is sharp.
- The 2nd AC leaves the frame fast and quietly, out of the actors' eyelines.
- The camera operator says "Set" once the frame is back, and the director calls "Action."
With two cameras on one board, the 2nd AC says "A and B common mark" before the clap, so both camera teams know one clap serves both. After a take that rolled is cut, the take number goes up by one. A rehearsal that never rolled keeps the same number.
What to write on the board
Production, director and DP (or camera operator) go on at the start of the day and stay up. The date is the shoot day and stays up all day, even on a night that runs past midnight. Roll, scene and take change through the day.
| Scene | The scene number from the script. The first setup is the number alone, such as 12. Each new camera position or lens on that scene adds a letter: 12A, then 12B. I and O are left out because they look like 1 and 0, and many crews also skip S and Z, which can look like 5 and 2. |
|---|---|
| Take | Starts at 1 on each new setup. Each time the camera rolls again on that setup is the next take. |
| Roll | The camera's card or roll, with the camera letter: A004 is camera A's fourth card. It should match the camera report. |
| Other | The frame rate when the shot is off-speed, INT or EXT, DAY or NIGHT, and MOS when the take has no sound. |
Head slate
The head slate is the normal one, at the start of the take. The board should be readable in the first frames the camera records, so the clip's thumbnail is the board. Sticks open while the scene and take are called, one clap, board held still, then out.
MOS: no sound on the take
MOS on a slate means the take is shot without sync sound. Cutaways, drive-bys and off-speed shots are often shot that way. If sound is rolling in sync, it is not MOS, and you clap. Write MOS on the board. Hold the sticks closed, or put a hand between them, so the editor does not go looking for a clap that has no sound. Call the scene and take, and do not clap. Crews say MOS stands for "mit out sound"; the origin is a story told on sets, not a standard.
Tail slate
A tail slate (also called an end board) marks the take at the end instead of the start. It is used when the head can't be slated: the shot starts on a sleeping actor, the camera is already moving, or the board would cost the moment.
Agree before the take that it will be tail slated, so camera and sound keep rolling after the action ends. At the end, the board goes into frame upside down with the sticks open. The upside-down board tells the editor this mark belongs to the take before it, not the head of the next one. Call it out loud, "Tail slate, scene twelve Apple, take three," so it is on the soundtrack. Then clap. Camera and sound cut only after that clap, even if the director has already cut the actors. Write tail slate on the camera and sound reports so editorial looks at the end of the clip.
Crews disagree on one step: some clap with the board still upside down, others show it upside down and turn it upright before the clap so it is easier to read. The cheat sheet prints one procedure: upside down, call it, clap, then cut.
Second sticks
When the first clap is missed (the sticks closed out of frame, the board was blurred, or the mixer did not hear it) and camera and sound are still rolling, open the sticks, call "Second sticks" and clap again before Action. The take number stays the same. If the roll was already cut, the next roll is the next take.
Soft sticks
When the board has to be close to an actor's face, tell the actor, call "Soft sticks," and close the sticks gently. The sticks still meet, so the picture has a frame to sync, and at that distance the mic still hears it. If the mixer misses it, they will ask for second sticks.
The shot log
The board is the mark. The log is what the editor reads later. The 2nd AC keeps a camera report for each card and the mixer keeps a sound report for each sound roll; both templates are free on this site as CSV and printable PDF.
Take Slate is a digital clapperboard app for iPhone, iPad and Android. Scene, take and roll fill the screen; tapping the striped sticks flashes the screen white and plays a beep, and the take goes into a shot log. The scene sheet offers the next setup letter, skipping I, O, S and Z. Each take can carry flags for MOS, pickup (PU, the take starts again part way in), series (SER, several pieces rolled without cutting), tail slate (TAIL) and second sticks (2ND STICKS in the log). With MOS on, tapping the sticks logs the take with no flash and no beep. Tail turns the board upside down for the clap and back upright a second later. 2nd sticks claps again on the take just logged, without changing the take number. The log's clock is the phone's time of day, not camera timecode. Share CSV sends the log through the phone's share sheet. The app and its CSV are free. Take Slate Pro is US$9.99 once and adds a PDF shot log and Wrap day.
Get it on the App StoreGet it on Google Play
No phone at hand? Film slate runs in the browser.